Browse Prior Art Database

The Cosmic Collector

IP.com Disclosure Number: IPCOM000213561D
Publication Date: 2011-Dec-21
Document File: 34 page(s) / 6M

Publishing Venue

The IP.com Prior Art Database

Abstract

Hello dear friends, I am here to Reveal to you how to make an energy collecting device. One that Can Generate 90,000 watts at 1500 Volts at a height of 36 feet. It’s time we take off the chains that bind us. Time to step into the light of ancient wisdom, time to rid ourselves of the blinders put there to keep us enslaved. Many people are now awakening and the time for disclosure is now. The device I will describe will be for receiving power from the universe of energy that is omnipresent.

This text was extracted from a PDF file.
This is the abbreviated version, containing approximately 9% of the total text.

Page 01 of 34

Hello dear friends, I am here to Reveal to you how to make an energy collecting device. One that Can Generate 90,000 watts at 1500 Volts at a height of 36 feet. It's time we take off the chains that bind us. Time to step into the light of ancient wisdom, time to rid ourselves of the blinders put there to keep us enslaved. Many people are now awakening and the time for disclosure is now. The device I will describe will be for receiving power from the universe of energy that is omnipresent.

HOW TO CONSTRUCT THE COSMIC COLLECTOR-

Height 36 feet. Generating 90,000 watts at 1500 Volts at 6ft + sea Level By the Coast.


Page 02 of 34

The Cosmic Collector is made up of
1 Copper Tube Wrapped In A coil, Laying In a Teflon Dish


1 Metal Plate Buried Flat In the Ground


1 12 volt Deep Cycle Lead Acid Battery


Page 03 of 34


2 Safety Disconnect Switches (high voltage circuit breaker)


A Good Sized Quantity of Quarts Crystals And Quartz Sand


1 1N4007 Diode


12 Gauge (12 AWG) Copper Wire (30 feet)


Page 04 of 34


6 Gauge (6 AWG) Copper Wire (10 feet)


2 Gauge (2 AWG) Copper Wire (50 feet)


4 Schottky Full Wave Bridge Rectifier 95SQ015 Diodes (Made By Vishay)


1 Large E.C.M. Also Known As a Brushless DC Motor


Page 05 of 34


A few dozen Copper Screws


8 Copper Wing Nuts


2 Dozen Copper Nuts


Several Copper Saddle Clips (3/4")


Page 06 of 34


(6) 6 volt Batteries


1 DC to AC Inverter


1 CRT Flyback Transformer


1 Auto Transfer Switch


Page 07 of 34


40 feet of 3 inch PVC pipe


1 Sliding Ring Joint

CONSTRUCTION

To construct the coil you will need 51.25 feet of three quarter inch diameter copper tubing. Ideally a very soft copper, called Type K Annealed Copper Tubing. Most likely you will find 60 feet of Type L Copper tubing coiled in a box at a hardware store such as Lowes. This is fine, it is just harder to bend.


There are different types of copper. six "tempers" (soft), (cold rolled), (cold rolled, high yield), (half hard), (three quarter hard), and (hard)

Take the copper tubing and wind it in a right hand spiral, keeping 7/8ths to 1 inch spacing in between the layer so of the coil. This even spacing is important and is called the Reluctance Gap. This helps Create The Vortex. The coil needs to have 9 turns, and total 37.5 inches in diameter.


Magnetic Reluctance aka Magnetic Resistance is a concept used in the analysis of magnetic circuits. It is analogous to resistance in an electrical circuit, but rather than dissipating magnetic energy it stores magnetic energy. In likeness to the way an electric current to follow the path of least resistance, a magnetic field causes magnetic flux to follow the path of least magnetic reluctance.

As you will notice this coil has much more surface area than a regular copper wire coil as used in a Bedini monopole. Surface area is vital to harnessing energy in this device.

You may either have a custom copper coil made for you, or more cheaply you and your friends can bend it yourselves. You can create a bending jig guide out of wood. See...